At least with Molex and others, you can guess at part numbers based on product family and pin count. Who created their part numbering scheme?!?! Their part marking has no rhyme or reason to it. Oh, and one last minus for AMP connectors in general. Those require a sledge hammer to get them installed! Can often find used ones on ebay.Ĭontact = 86016-3 (not 571-860163 as above)ĭon't try the intermediate or high pressure contacts with high pin count connectors. Minus -> Good crimps with these pretty much require using the AMP Certi-crimp crimpers.VERY expensive. The place is catalogued as Civil by the U.S. I have had some of these contacts actually break off the locking tang and push back out through the back of the connector. The Township of Fawn Creek is located in Montgomery County, Kansas, United States. Minus -> even with the low pressure contacts (part number 86016-3), about 27 box contacts can be a real bugger to push onto the header. Plus -> Box contacts can't be beat for reliability. Plus -> Somewhat affordable (but considerably higher than the old Molex plugs were). Plus -> Available in a wide variety of sizes all the way up to 36 pin. An easily findable version has your expected square plastic molex 'pins' that house the actual crimped pins, with what one might call the 'upper left' and 'lower right' being tombstone. If it does, then the drivers will work, it’s just a matter of the slot then.First - most AMP connectors are first rate. I've researched to the point of despair (digikey, mouser, amp, molex, others.) trying to identify this variation of your everyday 4-pin, 2-row molex pin plug. You can run the installer to see if it works before purchasing the card. The only way to know for sure would be to try it, and if you do need to return it we make it easy to get a full refund from Amazon for 30 days.Īs far as drivers go, there’s an installer package that should install the proper drivers for your version. Pitch (mm): Current (MAX): Wire Size: Voltage (MAX): Termination Style: 2.00mm: 2. I had a quick look the specs for the HP ML 110 G5 and it looks like there are two PCI-e X8 slots with X1 link but I’m not exactly sure if that’s compatible. Molexs Micro-Latch connector system provides a reliable connection interface for industry- standard 2.00mm wire-to-board applications. Thumbdrives are designed to work in a standard USB port, so there shouldn’t be any exceptions for USB 3.0.įrom what I can tell there’s no PCI-e 1x slot in your target machine. The reason for the external power to hardrives is that they are often designed to use more power than the USB spec allows so they come with an AC adapter (or a double headed cable) to draw from. In fact, many people run without it connected. Thanks for your post regarding PCI-e USB3.0 card and your HP ML 110 G5 Server.įirst, the good news… even though our PCI-e USB 3.0 card has a molex connector to connect to the power supply, we’ve never run across a case where it’s necessary. Thanks for the additional info, let me know what you find, The PCI-e bus is able to provide enough power to the card to cover the 900mA per port so I suspect the Tape Drive unit is pulling more than this ammount.Ĭan you say which operating system you have and which power supplies your Power Edge Servers have? You maybe able to use a splitter on your power connectors to get power to the card, but it’s not likely to stop the over current messages. Make sure you are using a USB 3.0 cable, as a 2.0 cable will cause the system to negotiate down to the USB 2.0 spec and the OS will then expect 500mA, max. USB 3.0 allows 900mA per port and a self powered device shouldn’t be pulling more than that. ![]() ![]() ![]() We haven’t seen an issue like this or USB 3.0 tape drives in the past so working in parallel with the Tape Drive manufacturer may be useful. It’s unusual for a device to trigger over current messages on our PCI-e card, especially when it’s self powered. Molex provides automotive bulb, camera and SIP sockets for a variety of industries including automotive and consumer electronics. Thanks for posting your question, we’ll be happy to help.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |